Design and implementation of low mass short backfire antennas using additive manufacturing
| dc.contributor.author | Aragbaiye, Yewande Mariam | |
| dc.contributor.examiningcommittee | Ferguson, Philip (Mechanical Engineering) | |
| dc.contributor.examiningcommittee | Shafai, Cyrus (Electrical and Computer Engineering) | |
| dc.contributor.supervisor | Isleifson, Dustin | |
| dc.date.accessioned | 2024-03-01T16:36:37Z | |
| dc.date.available | 2024-03-01T16:36:37Z | |
| dc.date.issued | 2024-02-22 | |
| dc.date.submitted | 2024-02-23T17:53:18Z | en_US |
| dc.degree.discipline | Electrical and Computer Engineering | en_US |
| dc.degree.level | Master of Science (M.Sc.) | |
| dc.description.abstract | This thesis presents research into the design of low-mass short backfire (SBF) antennas with enhanced performance. In the first section of this thesis, modern techniques that can be utilized to decrease the mass of the aluminum SBF antenna were introduced. Two different antenna designs were developed using additive manufacturing and perforation techniques. The first design was created by manufacturing the antenna using additive manufacturing techniques, resulting in a significant reduction in mass. Simulations were conducted on this design to analyze the impact of additive manufacturing on the antenna’s performance. The results indicated that the gain was significantly affected by high levels of surface roughness introduced during the manufacturing process. The second low-mass antenna design, the perforated 3D-printed SBF antenna, combines additive manufacturing and perforation techniques. Parametric studies were conducted on this antenna to determine the optimal size, shape, and arrangement of perforations to achieve the best mass reduction and gain results. Simulation studies found that the antenna with a 3x37 circular array of perforations on its rim, each with a radius of 4.5 mm, performed the best. The simulated results were validated by fabricating and measuring the antennas. The mass of the 3D-printed and perforated 3D-printed SBF antennas were approximately 70% and 80% lighter than the aluminum antenna, respectively, while maintaining minimal loss in gain. The second part of this thesis discusses the enhancement of gain and bandwidth in the SBF antenna. This was done by flaring the rim to increase the aperture size of the antenna. Simulation studies were conducted to examine the impact of rim flaring and rim height on antenna performance. The results of these studies indicate that this technique significantly improved both the gain and bandwidth of the antenna while having minimal effect on the cross-polarization ratio. To further enhance the bandwidth, an iris was introduced to the waveguide feed aperture to obtain better impedance matching. The antenna was then manufactured and tested to confirm the accuracy of the simulations. The measured and simulated results were in excellent agreement. | |
| dc.description.note | May 2024 | |
| dc.description.sponsorship | Research Manitoba #5645 IPOC GRANT Natural Resources Canada (NRCan) (grant number OSRC-04) | |
| dc.identifier.uri | http://hdl.handle.net/1993/38032 | |
| dc.language.iso | eng | |
| dc.rights | open access | en_US |
| dc.subject | Short backfire antenna | |
| dc.subject | Additive manufacturing | |
| dc.subject | Mass reduction | |
| dc.subject | Gain enhancement | |
| dc.subject | Bandwidth enhancement | |
| dc.subject | Aperture flaring | |
| dc.subject | Perforation technique | |
| dc.title | Design and implementation of low mass short backfire antennas using additive manufacturing | |
| dc.type | master thesis | en_US |
| local.subject.manitoba | yes | |
| oaire.awardNumber | RGPIN-2017-04974 | |
| oaire.awardTitle | Technology Advancement for Microwave Remote Sensing of Sea Ice | |
| project.funder.identifier | https://doi.org/10.13039/501100000038 | |
| project.funder.name | NSERC Discovery Grant |